We've just launched a new two-way globe control valve!
The new ADCATrol V16/2 is a series of single seated, two-way globe control valves available in EN and ASME standards and designed for simple process engineering and industrial applications, with non-critical operating conditions. These valves can be assembled with pneumatic, hydraulic or electric actuators, for modulating and shut-off control tasks.
MAIN FEATURES
Sizes: DN 15 to DN 100 ; 1/2” to 4”
Material: SG iron, carbon steel and stainless steel
Connections: Flanged EN 1092-2 PN 16, Flanged EN 1092-1 PN 16 or PN 40 & Flanged ASME B16.5 Class 150 or 300
Check out the updated datasheets for more information on these models:
FLT News | Three new steam traps were just launched!
The FLT29TW, FLT39TW and FLT49TW are our new “twin” high capacity (up to 45000 kg/h) float and thermostatic steam traps. These new models feature a central mechanism which improves ease of maintenance and change in flow direction, a wider operating pressure range and many new options.
MAIN FEATURES / FLT29TW
Sizes: 3” to 4” – DN 80 to DN 100
Material: SG Iron
Connections: Flanged EN 1092-1 PN 16 - Flanged ASME B16.5 Class 150
MAIN FEATURES / FLT39TW
Sizes: 3” to 4” – DN 80 to DN 100
Material: Carbon steel
Connections: Flanged EN 1092-1 PN 16 or PN 40 - Flanged ASME B16.5 Class 150 or 300
MAIN FEATURES / FLT49TW
Sizes: 3” to 4” – DN 80 to DN 100
Material: Stainless steel
Connections: Flanged EN 1092-1 PN 16 or PN 40 - Flanged ASME B16.5 Class 150 or 300
Check out the datasheets for more information on these models:
The SH25S series centrifugal humidity separators allow seamless integration into the pipework due to their low-profile in-line design.
These separators are composed by an inlet plate with a propeller blade design which promotes high speed centrifugal motion and allows removal of up to 99% of water droplets and solid entrained particles from the medium. The unit has no moving parts and does not require any maintenance. It’s one of the simplest ways to improve steam quality and heat transfer efficiency on your steam system, in main lines or at the point of use.
MAIN FEATURES
Sizes: 1/2” to 6”; DN 15 to DN 150
Material: Carbon steel
Connections: Flanged EN 1092-1 PN 16 or PN 40 / Flanged ASME B16.5 Class 150 or 300
Check out the datasheet for more information on this model.
The ADCAPure P130 line of sanitary pressure regulators specially designed for clean gases is complete!
Available from 1/2'' to 11/2'’, with clamp ferrule or tube weld ends, spring or dome loaded and flow rate capacities well distributed between the models to ensure the best performance with minimum droop.
MAIN FEATURES
Sizes: 1/2'' to 11/2 ; DN 08 to DN40
Connections: ASME BPE, DIN and ISO clamp ferrules or tube weld (ETO) ends
We have just announced the launch of a completely new, modern website.
A thoroughly redesign process has been undergone to ensure that our visitors locate the desired products and documentation easily.
The interface is now much more user-friendly and responsive, making it a powerful and useful tool improved for all platforms and devices, so it can be accessed anywhere, anytime, with the best results.
The Download Center was specially designed for quick document location. With a simple click, users are now able to find all products and details they are searching for.
Keep up to date on product news, trade shows, events and company announcements in the News & Events section and browse through all the website, enjoying the pleasant design and practical functionalities.
When a steam boiler is in operation there is continuous evaporation of boiler water wich causes an undesirable increase in TDS (Total Dissolved Solids) concentration. A typical problem that results from this is water foaming, which leads to reduce boiler performance and wet steam. Furthermore, dissolved and suspended solids will carry over into the steam lines, contaminating valves, tubes, heat exchangers and steam traps, leading to corrosion, scaling and erosion. For these reasons, a certaing amount of boiler water must be discharged continuously or periodically to ensure TDS concentration is kept within the recommended parameters.
The ADCATrol VPC26 is a control valve specially designed for this purpose and features a multi-stage trim to progressively reduce the energy of the fluid. This makes it ideal for discharge of boiler blowdown at high differential pressures where flashing is a concern.
The valve is suitable for both continuous and on/off TDS control via a PA series reverse action pneumatic actuator or AV saeries fail-safe spring return actuator.
The ADCAMat PPT14 automatic pump trap is specially
recommended where stall condition may occur due to poor
steam trap condensate discharge capacity, caused by temporary
insufficient pressure drop.
The equipment combines the features of a float steam trap and a
pressure operated pump, in one single unit.
Whenever the steam trap function is incapable of draining
condensate, the pump function is activated (using external steam
pressure).
The pump replaces the necessary positive pressure
to lift the condensate to the return system, before water logging
occurs, avoiding water hammer and consequent noise, equipment
damage, corrosion, unstable temperature control, etc.
MAIN FEATURES
Compact design
No electric requirements
No NPSH issues
Operation under vacuum conditions
No motive or flash steam is lost
Low filling head for minimal installation space requirements
Product news: SRV with pneumatic lifting device is now available
The pneumatic lifting device complements now the offering of options for the ADCAPure SRV range of safety relief valves and allows remote operation of the valve which is ideal for cleaning (CIP) and sterilization (SIP) procedures. This specially designed valves for the most demanding aseptic and hygienic applications are completely machined from 316L bar stock material and are approved according to ISO 4126.
One more year distinguished as a leading and excellence company
VALSTEAM has been distinguished with the distinction of PME Líder (leading small and medium-sized enterprise) and PME Excelência (small and medium-sized company of excellence) for almost ten consecutive years and this year was no different! These are statutes of business reputation created by IAPMEI as a way of recognizing the merit of Portuguese Small and Medium Enterprises that have superior performances in terms of the best rating quotations and economic and financial indicators. ..
In February a mystery was unraveled: the brand new VPA26/2 Intermittent Boiler Blowdown valve was launched! This valve features clamped-in seats, simplifying maintenance procedures and reducing downtime costs! It has a redesigned stem packing and guiding system for a smoother maintenance-free operation. For more information on features and options please check the datasheet.